Filtered by vendor Juniper
Subscriptions
Filtered by product Mx150
Subscriptions
Total
55 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2021-0228 | 1 Juniper | 11 Junos, Mx10, Mx104 and 8 more | 2021-07-23 | 6.5 Medium |
| An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker sending specific Layer 2 traffic to cause Distributed Denial of Service (DDoS) protection to trigger unexpectedly, resulting in traffic impact. Continued receipt and processing of this specific Layer 2 frames will sustain the Denial of Service (DoS) condition. An indication of compromise is to check DDOS LACP violations: user@device> show ddos-protection protocols statistics brief | match lacp This issue only affects the MX Series platforms with Trio-based MPC. No other products or platforms are affected. This issue affects: Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2; | ||||
| CVE-2020-1608 | 1 Juniper | 17 Junos, Mx10, Mx10003 and 14 more | 2021-07-21 | 7.5 High |
| Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions starting from 17.3R2-S4, 17.3R3-S2 and later releases, prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions starting from 17.4R2 and later releases, prior to 17.4R2-S7,17.4R3; 18.1 versions starting from 18.1R2-S3, 18.1R3 and later releases, prior to 18.1R3-S6; 18.2 versions starting from18.2R1-S1, 18.2R2 and later releases, prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R2-S6. | ||||
| CVE-2020-1650 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2021-07-21 | 7.5 High |
| On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1. | ||||
| CVE-2020-1649 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2021-07-21 | 7.5 High |
| When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability. | ||||
| CVE-2020-1627 | 1 Juniper | 3 Junos, Mx150, Vmx | 2021-07-21 | 7.5 High |
| A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by default in performance mode. This issue can only be triggered by traffic destined to the device. Transit traffic will not cause the riot daemon to crash. When the issue occurs, a core dump and riot log file entry are generated. For example: /var/crash/core.J-UKERN.mpc0.1557255993.3864.gz /home/pfe/RIOT logs: fpc0 riot[1888]: PANIC in lu_reorder_send_packet_postproc(): fpc0 riot[6655]: PANIC in lu_reorder_send_packet_postproc(): This issue affects Juniper Networks Junos OS: 18.1 versions prior to 18.1R3 on vMX and MX150; 18.2 versions prior to 18.2R3 on vMX and MX150; 18.2X75 versions prior to 18.2X75-D60 on vMX and MX150; 18.3 versions prior to 18.3R3 on vMX and MX150; 18.4 versions prior to 18.4R2 on vMX and MX150; 19.1 versions prior to 19.1R2 on vMX and MX150. This issue does not affect Junos OS versions prior to 18.1R1. | ||||
| CVE-2019-0065 | 1 Juniper | 18 Junos, Mx10, Mx10003 and 15 more | 2021-07-21 | 7.5 High |
| On MX Series, when the SIP ALG is enabled, receipt of a certain malformed SIP packet may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending a crafted SIP packet, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on MX Series: 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S6 ; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S3; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2. | ||||
| CVE-2019-0063 | 1 Juniper | 18 Junos, Mx10, Mx10003 and 15 more | 2021-07-21 | 7.5 High |
| When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series. | ||||
| CVE-2020-1655 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2021-07-21 | 5.3 Medium |
| When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability. | ||||
| CVE-2021-0264 | 1 Juniper | 21 Junos, Junos Os Evolved, Mx10 and 18 more | 2021-04-30 | 7.5 High |
| A vulnerability in the processing of traffic matching a firewall filter containing a syslog action in Juniper Networks Junos OS on MX Series with MPC10/MPC11 cards installed, PTX10003 and PTX10008 Series devices, will cause the line card to crash and restart, creating a Denial of Service (DoS). Continued receipt and processing of packets matching the firewall filter can create a sustained Denial of Service (DoS) condition. When traffic hits the firewall filter, configured on lo0 or any physical interface on the line card, containing a term with a syslog action (e.g. 'term <name> then syslog'), the affected line card will crash and restart, impacting traffic processing through the ports of the line card. This issue only affects MX Series routers with MPC10 or MPC11 line cards, and PTX10003 or PTX10008 Series packet transport routers. No other platforms or models of line cards are affected by this issue. Note: This issue has also been identified and described in technical service bulletin TSB17931 (login required). This issue affects: Juniper Networks Junos OS on MX Series: 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved on PTX10003, PTX10008: All versions prior to 20.4R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1. | ||||
| CVE-2021-0238 | 1 Juniper | 15 Junos, Mx10, Mx10000 and 12 more | 2021-04-29 | 5.5 Medium |
| When a MX Series is configured as a Broadband Network Gateway (BNG) based on Layer 2 Tunneling Protocol (L2TP), executing certain CLI command may cause the system to run out of disk space, excessive disk usage may cause other complications. An administrator can use the following CLI command to monitor the available disk space: user@device> show system storage Filesystem Size Used Avail Capacity Mounted on /dev/gpt/junos 19G 18G 147M 99% /.mount <<<<< running out of space tmpfs 21G 16K 21G 0% /.mount/tmp tmpfs 5.3G 1.7M 5.3G 0% /.mount/mfs This issue affects Juniper Networks Junos OS on MX Series: 17.3R1 and later versions prior to 17.4R3-S5, 18.1 versions prior to 18.1R3-S13, 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2; This issue does not affect Juniper Networks Junos OS versions prior to 17.3R1. | ||||
| CVE-2021-0251 | 1 Juniper | 17 Junos, Mx10, Mx10003 and 14 more | 2021-04-27 | 8.6 High |
| A NULL Pointer Dereference vulnerability in the Captive Portal Content Delivery (CPCD) services daemon (cpcd) of Juniper Networks Junos OS on MX Series with MS-PIC, MS-SPC3, MS-MIC or MS-MPC allows an attacker to send malformed HTTP packets to the device thereby causing a Denial of Service (DoS), crashing the Multiservices PIC Management Daemon (mspmand) process thereby denying users the ability to login, while concurrently impacting other mspmand services and traffic through the device. Continued receipt and processing of these malformed packets will create a sustained Denial of Service (DoS) condition. While the Services PIC is restarting, all PIC services will be bypassed until the Services PIC completes its boot process. An attacker sending these malformed HTTP packets to the device who is not part of the Captive Portal experience is not able to exploit this issue. This issue is not applicable to MX RE-based CPCD platforms. This issue affects: Juniper Networks Junos OS on MX Series 17.3 version 17.3R1 and later versions prior to 17.4 versions 17.4R2-S9, 17.4R3-S2; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect: Juniper Networks Junos OS versions prior to 17.3R1. | ||||
| CVE-2020-1665 | 1 Juniper | 17 Ex9200, Junos, Mx10 and 14 more | 2021-02-05 | 5.3 Medium |
| On Juniper Networks MX Series and EX9200 Series, in a certain condition the IPv6 Distributed Denial of Service (DDoS) protection might not take affect when it reaches the threshold condition. The DDoS protection allows the device to continue to function while it is under DDoS attack, protecting both the Routing Engine (RE) and the Flexible PIC Concentrator (FPC) during the DDoS attack. When this issue occurs, the RE and/or the FPC can become overwhelmed, which could disrupt network protocol operations and/or interrupt traffic. This issue does not affect IPv4 DDoS protection. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). Please refer to https://kb.juniper.net/KB25385 for the list of Trio-based PFEs. This issue affects Juniper Networks Junos OS on MX series and EX9200 Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.2 versions prior to 18.2R2-S7, 18.2R3, 18.2R3-S3; 18.2X75 versions prior to 18.2X75-D30; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2. | ||||
| CVE-2020-1680 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2021-02-05 | 5.3 Medium |
| On Juniper Networks MX Series with MS-MIC or MS-MPC card configured with NAT64 configuration, receipt of a malformed IPv6 packet may crash the MS-PIC component on MS-MIC or MS-MPC. This issue occurs when a multiservice card is translating the malformed IPv6 packet to IPv4 packet. An unauthenticated attacker can continuously send crafted IPv6 packets through the device causing repetitive MS-PIC process crashes, resulting in an extended Denial of Service condition. This issue affects Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S7; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S11, 17.4R3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2. | ||||
| CVE-2021-0205 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2021-01-21 | 5.8 Medium |
| When the "Intrusion Detection Service" (IDS) feature is configured on Juniper Networks MX series with a dynamic firewall filter using IPv6 source or destination prefix, it may incorrectly match the prefix as /32, causing the filter to block unexpected traffic. This issue affects only IPv6 prefixes when used as source and destination. This issue affects MX Series devices using MS-MPC, MS-MIC or MS-SPC3 service cards with IDS service configured. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S10 on MX Series; 17.4 versions prior to 17.4R3-S3 on MX Series; 18.1 versions prior to 18.1R3-S11 on MX Series; 18.2 versions prior to 18.2R3-S6 on MX Series; 18.3 versions prior to 18.3R3-S4 on MX Series; 18.4 versions prior to 18.4R3-S6 on MX Series; 19.1 versions prior to 19.1R2-S2, 19.1R3-S3 on MX Series; 19.2 versions prior to 19.2R3-S1 on MX Series; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1 on MX Series; 19.4 versions prior to 19.4R3 on MX Series; 20.1 versions prior to 20.1R2 on MX Series; 20.2 versions prior to 20.2R2 on MX Series; | ||||
| CVE-2019-0007 | 1 Juniper | 17 Junos, Mx10, Mx10003 and 14 more | 2020-08-24 | N/A |
| The vMX Series software uses a predictable IP ID Sequence Number. This leaves the system as well as clients connecting through the device susceptible to a family of attacks which rely on the use of predictable IP ID sequence numbers as their base method of attack. This issue was found during internal product security testing. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1F5 on vMX Series. | ||||